Share Categories Channel
1/5
12V Dual Battery MPPT Solar Charge Controller Battery Charger image 112V Dual Battery MPPT Solar Charge Controller Battery Charger image 2

12V Dual Battery MPPT Solar Charge Controller Battery Charger

Shenzhen Ouxiang Electronics Co., Ltd.

Price $99.00 / Pieces
Mini Order
-+Subtotal: $990
Availability In Stock
Purchase details

Payments:

Returns&Refunds:

Eligible for returns and refunds View More

MPPT5030-DUO
24V-310W
12V/6A
12-24/12V
Lead-Acid Battery Charger
Solar Charger
Half-Bridge Charger
30A 50V
Gel, Sealed, Flooded, LiFePO4, Lithium-Ion
Support
Support
99.8%
50V
OEM
Neutral
neutral
Shenzhen
Product Description


Dual battery MPPT Solar Charge Controller Battery Charger

 
 Features
This is a all-automatic DC-DC battery charger, you can use the battery (12V) to charge the battery (12V) (B2B), specially designed for RVs, exposed cars, campers, ships, etc.

Technical Data
 
item
value
Place of Origin
Shenzhen
Brand Name
Oxiang/ OEM
Model Number
MPPT5030-DUO
Type
MPPT
Application
Charger Controller, Wind Controller, Collector Controller, Water Heater Controller, Solar Working Station, Lighting Controller, Thermal Controller, Voltage Controller, Solar System Controller
Work Time (h)
24H
Max PV Voltage
24V
Certificate
CE
Warranty
24 Months
Maximum solar panel voltage
12V/24V
MPPT tracking efficiency
99.8%
Product size
14.7*7.9*4.2 cm
Box Size
21*18*6.5 cm 


B2B Operation

mobile operation from dynamo and starter battery (Battery to Battery):

it refers to charging the main battery through dynamo and starter battery, .If it is not used in the Vehicle , you can also use one battery (12V) to charge another
  1. . The efficient charging converter (booster) allows full charging of the board battery during driving.
  2. . It increases/reduces the voltage to the level, which is required for precise charging of the board battery with the optimum characteristic line of charging.
  3. . The simultaneously supplied 12 V consumers are protected against overvoltage and voltage fluctuations.

Further Characteristics of the Unit
 
  • The output voltage is stabilized, free of peaks, smoothed and filtered.
  • Galvanic isolation between input and output:
  • No overvoltage at the output and thus protection of the consumer if the ground line is lost.
  • Clean, undisturbed mass ratios, even with long supply lines.
  • Stable operating voltage on site in mobile operation, e.g. Containers, trailers, roll containers etc.
  • Filtering and suppression of disturbances on the input to the output side.
  • Fully automatic continuous operation: The DC-DC converter can constantly work with the battery
  • Surveillance-free operation: multiple protection against overload, overheating, over voltage, short circuit, Misconduct and deep discharge of the battery through electronic regulation to complete
  • Switch off by built-in safety switch.
Function

 

Security guidelines

Intended use:
The DC-DC converter was built on the basis of the valid safety guidelines. The use may only be:
  1. On lead-acid, lead-gel or lead AGM or LiFePO4 batteries of the specified nominal voltage.
  2. With the specified cable cross-sections for inputs and outputs.
  3. With fuses of the specified strength near the battery to protect the wiring between the batteries and DC-DC converter connections.
5. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases as well as in a non-condensing environment.
The device must never be used in places where there is a risk of gas or dust explosion consists!
 

Installation of the Unit
  1. . Install the charger near the board supply battery I (for short charging cables) at a clean, even and hard mounting surface,which is protected from moisture, humidity and aggressive battery gases. The unit can be installed in any position.
  2. . To be installed in a moisture-proof, water-proof place, corrosion-proof place
  3. . When the charging controller is working, the fan will bring out heat, so when installing, ensure that there is at least 10cm of space behind the charger controller
  4. . Choose the appropriate cable specifications, length and fuse specifications, reverse connection of the battery will cause serious damage to the equipment

Why Choose us?

> Oxiang is located in Shenzhen, China, a new type of city in rapid development. We focus on CCTV Camera researching and manufacturing from 2006;

> Sales person provide Pre-sales and after-sales service; Professional engineers are always standby and assist offer solutions;

> Cooperate with multiple departments to complete raw material procurement, production, inspection, delivery and other steps;

> The product comes with a one-year warranty.

Send Message

Content*

Your Name

Tel*

Email*

Shop Cart