COLO-3180A
220V/380V
12 Months
Flexible
Assembly
CE, CE, ISO
Non Automation
Intelligent Manufacturing
Non Flow Production Line
Product Line
Powder Painting Drying
Manual
3000X1800X1800mm
15 Days
CE
Electrostatic Spraying Equipment
Hardware Spraying Equipment
Powder
Manual
New
Online
HICOLO
Wooden Carton
CE
China
8424899990
Product Description
We are a leading Brand in the field of offering clients precision designed and optimum functionality based range of Spray booth and Curing Ovens.
These ovens are widely appreciated for features like precision engineering, high efficiency as well as corrosion resistance features.
After spraying the part, the polymerization of the applied powder coating can be done by heating it in a paint polymerization oven that runs on gas.
Specific to this type of equipment is the use of a blast-lamp to heat the oven.
CE Powder polymerization oven Model COLO-3180A
Installation and operation of Electrostatic Powder Curing Oven
1, Make sure the ground is level.
2 Clean the inner of the oven, close the door.
3 Make the workpieces which will to be cure ready. About half an hour.
4 Set the temperature as you required, normally for 180°C-200°C. set the time you need to cure, such as 25 minutes (this will according to thickness of your workpiece, if for thin,then 20mins,for thickness about 25mins).open the door, push the workpieces into the oven,close the door.
5 Turn on the power switch,and then press the bottom of turn on
6 After the temperature reach to the value we setted, the time will begin to change.(you don't need to operate, it is automatic change )
7 When hear the bell ring, press the bottom of turn off ,push out the workpiece which has been cured. Push into the next batch.
8 Please lift down the the workpiece which from the oven after cured ,after it will be cooled.
We also produce powder coating spray booth, powder coating machines, and powder spray gun. Here some pictures for your reference to know more about our company.
These ovens are widely appreciated for features like precision engineering, high efficiency as well as corrosion resistance features.
After spraying the part, the polymerization of the applied powder coating can be done by heating it in a paint polymerization oven that runs on gas.
Specific to this type of equipment is the use of a blast-lamp to heat the oven.
CE Powder polymerization oven Model COLO-3180A
| Worksize Dimenstions | 1800x1800x3000mm |
| Over Dimensions | 2150x2100x3250mm |
| Power Supply | Electric/30KW |
| Voltage/Frequency | 380v/220v (50-60Hz) |
| Warm up time | 15-30mins (180 °C) |
| Temperature stability | < ± 3-5°C |
| Ventilation performace | 1133-2565m3/h |
| Motor power | 1.5KW |
| Circulation/Air flow | Vertical,variable through holes on the walls |
Installation and operation of Electrostatic Powder Curing Oven
1, Make sure the ground is level.
2 Clean the inner of the oven, close the door.
3 Make the workpieces which will to be cure ready. About half an hour.
4 Set the temperature as you required, normally for 180°C-200°C. set the time you need to cure, such as 25 minutes (this will according to thickness of your workpiece, if for thin,then 20mins,for thickness about 25mins).open the door, push the workpieces into the oven,close the door.
5 Turn on the power switch,and then press the bottom of turn on
6 After the temperature reach to the value we setted, the time will begin to change.(you don't need to operate, it is automatic change )
7 When hear the bell ring, press the bottom of turn off ,push out the workpiece which has been cured. Push into the next batch.
8 Please lift down the the workpiece which from the oven after cured ,after it will be cooled.
We also produce powder coating spray booth, powder coating machines, and powder spray gun. Here some pictures for your reference to know more about our company.
