Overview of Work Vehicle
new 20 meter multifunctional high-altitude work vehicle, driven with a C license, with a blue license plate. The chassis adopts the Jiangling Shunda National VI 115 horsepower Isuzu engine, 700R16 steel tire, electric glass, multifunctional steering wheel, hydraulic power, and other high-end original factory configurations.
Chassis configuration: Equipped with Jiangling 115 horsepower/single row cab, 3360 wheelbase, 7.00 steel wire tires, oil brakes, five speed gearbox, front axle 2 tons, rear axle 3.5 tons, with steering assistance, exhaust braking, original ABS, original air conditioning, and multifunctional steering wheel.
Upper configuration: work platform 1400x700x1150 ★ four hexagonal work arms, synchronous telescopic ★ 360 degree continuous rotation device ★ front V and rear H-shaped support legs, individually adjustable operation ★ work platform and ground remote control electrical operation ★ electro-hydraulic proportional control system, achieving stepless speed regulation ★ hydraulic automatic leveling system ★ high-strength aluminum alloy 360 degree rotating basket; The work platform has a load capacity of 200KG ★, with a maximum operating height of 25 meters and a maximum operating range of 14.5 meters.
The upper garment adopts segmented coating, electrophoretic process, imported full proportion valve, multifunctional work platform (extending 45 cm forward to increase the safety area for high-altitude workers), oil cylinder and balance valve are from well-known domestic manufacturers, and the whole vehicle is equipped with four operation devices (electric control, manual, remote control, emergency). The whole vehicle comes with four toolboxes, four hydraulic legs, which can be operated separately or linked for control. The legs are equipped with hydraulic locking devices, and the lower legs are locked, Hydraulic lifting is only possible after installation. Can be equipped with a 1-ton hoist, both hydraulic and electric (electric hoist can lift 200kg). Bring small flying arms for greater lifting height.
The characteristics of high-altitude work vehicles: There are control devices inside the work bucket and on the rotating seat, which can remotely control the start/stop, high/low speed of the engine. The action of the arm is controlled by an electro-hydraulic proportional valve, which has good stability. The work arm can rotate continuously 360 ° left and right, and the level of the work slot is automatically maintained by the connecting rod mechanism. When the main pump fails, the emerping, communication, airports, shipbuilding (repair), transportation, advertising, photography, etc.
Parameter configuration of straight arm telescopic aerial work vehicle:
1. The chassis adopts the euro VI chassis, equipped with air conditioning, and the steering wheel adopts hydraulic power assistance;
2. The disembarking leg operation box is equipped with lighting devices for convenient night work, and is equipped with a bi-directional vehicle level to ensure vehicle level and safety;
3. The arm frame is designed to rotate into one unit, avoiding assembly gaps caused by reassembly during production and increasing the space for using the walking platform;
4. Front X and rear H-shaped support legs, with good stability, can be operated simultaneously or independently and can achieve automatic leveling, suitable for various working conditions. All models come standard with a wash basin;
5. Computer control, automatic limit, dangerous work alarm, high safety performance. Get off the vehicle and have a display that displays the entire vehicle's operating conditions in real time;
6. Quadrilateral work arm, synchronous telescopic, compact structure, high work efficiency, and large work range. The telescopic oil cylinder, oil pipe, and cable tray are externally installed, and the chain telescopic mechanism makes it easier to observe the fault point and facilitate maintenance.
7. The boarding control is equipped with a display screen, and the disembarking is equipped with wireless remote control for convenient multi angle observation.
8. The disembarking leg operation box is equipped with lighting for convenient night work, and is equipped with a vehicle level to ensure vehicle level and safety.
9. The platform's left and right rotation adopts an imported enclosed swing cylinder or motor driven form, which is flexible, convenient, safe and reliable in operation.
Computer control, automatic limit, dangerous work alarm, excellent safety performance.
10. There is a display when getting off the car, which displays the working conditions of the entire vehicle in real time.
11. Quadrilateral four section work arm, synchronous telescopic, compact structure, high work efficiency, and large work range. The external expansion cylinder and chain expansion mechanism make it easier to observe the fault point and facilitate maintenance.
12. The entire vehicle's electrical system adopts a CAN bus control system, with neat and simple wiring.
13. The whole vehicle has three operations: platform operation, and can also be operated on the ground using wired or wireless, which is more convenient to observe the working space, safe and reliable, and high work efficiency.
PHOTOS 
| Main configuration parameters of a 25 meter blue card high-altitude work vehicle | ||||
| category | project | Unit data | Unit data | |
| Dimensional parameters Quality parameters Main performance parameters | Total length | mm | 5998 | |
| Total width | mm | 2050 | ||
| Total height | mm | 3100 | ||
| Driving parameters category | Number of passengers (including driver) | 2 | ||
| Total mass | kg | 4495 | ||
| Dimensional parameters Quality parameters Main performance parameters Driving parameters category Dimensional parameters Quality parameters Main performance parameters Driving parameters category | Rated load of work platform | kg | 200 | |
| Maximum homework height | m | 23 | ||
| Maximum working height and working amplitude | m | 3.9 | ||
| Maximum homework amplitude | m | 15 | ||
| The height of the homework at the maximum homework amplitude | m | 4.5 | ||
| Leg span | transverse | mm | 3720/2800 | |
| portrait | mm | 4070 | ||
| Arm frame amplitude change time | s | 60 | ||
| Arm rotation speed | s/r | 75 | ||
| Leg extension and retraction time | s | 40 | ||
| Dimensional parameters | Front overhang | mm | 1075 | |
| Rear overhang | mm | 1560 | ||
| Backward extension | mm | / | ||
| Wheelbase | mm | 3360 | ||
| Maximum driving speed | Km/h | 100 | ||
| Minimum ground clearance | mm | 195 | ||
| Approach angle | . | 20 | ||
| Departure angle | . | 11 | ||
Shandong Xiangjin International Trade co., LTD., founded in 2009, is located in Jining city in Shandong province economic development zone, covers an area of 200000 square meters,production workshop 50000 square meters,with automatic Laser cutting machine,Roll machine, Bending machine,and various Welding cutting equipment,the company has Design Department,Purchasing Department,Production Department,Sales Department,Operations,Finance Department,QC department,Logistics Department,After-sales Service Department, Finance Department, International Trade Department.
Existing staff 300 people, including 50 engineering and technical personnel, 30 senior engineers, in the full introduction of domestic and foreign technology and talent at the same time, actively independent research and development, professional engaged in concrete mixing truck, sanitation truck, and other complete sets of equipment research and development, production and sales.
Its main models are five sign five wheel concrete mixing truck, homemade four unlike mixing truck, six east wind mixing truck, three East wind mixing truck, crawler type mixing truck, rail type mixing truck, wet and dry dust suction truck, suction purification car, car crane, truck crane, spider crane, pile driver and so on.
Our products are all over the world, Laos, Vietnam, Myanmar, Philippines, India, Pakistan, Uzbekistan, Tanzania, Liberia and so on, customers are very satisfied with our product quality and high quality service guarantee!
Quality Control
1. 100% Raw materials incoming test;
2. Semi-finished product test ;
3. Finished product test 4. Battery charge aging test.
High Efficiency Our monthly output is 500pcs. Sample available in 1-7 days, and normal order delivery time is only 7-15 days.
After-Sales Service
1.Quick response to service demands.
2.Providing quality guarantee and corresponding maintenance service.
1. who are we?
We are based in Shandong, China, start from 2018,sell to Africa(45.00%),Southeast Asia(30.00%),Domestic Market(10.00%),South Asia(5.00%),North America(5.00%),South America(1.00%),Central America(1.00%),Western Europe(1.00%),Oceania(1.00%),Eastern Europe(1.00%). There are total about 301-500 people in our office.
2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;
3.what can you buy from us?
Mixer truck,Suction-type sewer scavenger,Vacuum sweeper,Concrete pump truck,Hydraulic aerial cage
4. why should you buy from us not from other suppliers?
Technology research and development, production and sales integration
5. what services can we provide?
Accepted Delivery Terms: FOB,CFR,CIF,EXW;
Accepted Payment Currency:USD,EUR,JPY,AUD,CNY;
Accepted Payment Type: T/T,L/C,Western Union;
Language Spoken:English,Chinese
